Compex-technologies NetPassage 18A Manual de usuario

1 Chapter 1: Introduction Introducing the Router His is a Dual Band Wireless A+G VPN Internet Router. It does not merely operate in wired networ

91 TELNET CLI Telnet CLI (Command Line Interface) The user may connect to the CLI (Command Line Interface) via a TELNET session to the default I

92 SSH CLI SSH CLI (Secure Shell Host Command Line Interface) SSH is designed and created to provide the best security when accessing another com

93 SSH CLI has a command line interface like shown below for example. NOTE Please refer to Appendix D for the list of commands available at

94 User Management User Management To add user: 1. Click Add button. 2. In Add User Entry Page, enter User Name, Password, Confirm P

95 Web Management Setup HTTPS (SSL) is supported in addition to the standard HTTP. HTTP (SSL) features additional authentication and encryption

96 Web service restarts automatically. Web session logouts. You may reconnect using the new web service using the relogin link displayed on the

97 Remote Management This feature is especially helpful for users who work away from the office or from home. The user only requires Internet acce

98 Universal Plug and Play (UPnP) The following are issues that can arise when using NAT: • Some network applications assume the IP address and po

99 Although NAT traversal does not solve all NAT-related issues, it allows several applications to run behind NAT-enabled devices. It is recommende

100 Parallel Broadband The router is equipped with the exclusive Parallel Broadband technology, which features scalable Internet bandwidth, Load Ba

2 Chapter 2: Getting to know your Router The following will help you get more acquainted with the rich suite of features offered by the router so

101 To Enable Parallel Broadband Parallel Broadband can be implemented when:  More than one access point is interconnected (LAN port to LAN port)

102 Static Address Translation (Only supported by Wireless Routing Client and Gateway) If you use a notebook for work at the office, it is probabl

103 Under the HHoommee UUsseerr FFeeaattuurreess command menu, click on SSttaattiicc AAddddrreessss TTrraannssllaattiioonn. You may

104 DNS Redirection DNS Redirection allows you to redirect DNS requests to a local or closer DNS server. This improves the response time and enable

105 Dynamic DNS Setup It is difficult to remember the IP addresses used by computers to communicate on the Internet. It gets even more complicated

106 To add a new Dynamic DNS to the list, click Add. Choice DDNS Provider page displays. There are two default providers that you can use.

107 There are two predefined DDNS providers. Please note that you need to be connected to the Internet to register your DDNS account. To select 2

108 Optional: In the Mail Exchanger field, enter the Static WAN IP address of the mail server configured to handle email for your domain. Selec

109 To select DtDNS as DDNS Service Provider Under the Choice column in the Choice DDNS Provider check the radio button for DtDNS. Click Next.

110 Chapter 9: Security Configuration The Security Configuration chapter covers:  Firewall Configuration  Firewall Logs  Packet Filtering 

3 Virtual AP (Multiple SSID) Virtual AP implements mSSID (Multi-SSID) This allows a single wireless card to be set up with up to 16 virtual AP conn

111 Firewall Configuration Follow these steps to configure the firewall. Firewall Configuration 1. Enable the firewall. You ca

112 More firewall rules can be added for specific security purposes. Rule Name : Enter a unique name to identify this firewall rule. Dispositi

113 congestion. Redirect Informs the host of a preferred route. Time exceeded Indicates that the Time-to-Live (TTL) of an IP datagram has expired

114 available selection options are abbreviated as follows: SEC – Security LSRR – Loose Source Routing Timestamp – Timestamp RR – Record Route SID

115 1. Rule Number ranges from 1 to40. Precedence is determined inascending order such that rule1

116 9. Similarly, determine theDestination Port. 10. Select from Check Options. 11. Select whether to l

117 Firewall Logs As described previously, from the Firewall Configuration page the data traffic to be logged by the router can be defined. The Fi

118 Packet Filtering With Packet Filtering enabled, the router examines all outgoing packets before deciding - according to predefined rules - whet

119 Follow these steps to setup packet filtering. Packet Filtering Clicking Change select Packet Filter Type. Select from three

120 4b). From the IP Address dropdown list, select whether to apply the rule to:  A Range of IP addresses. Define

4 Security Features You will be glad to learn about the security elements we have put in place to better protect your data and privacy.

121 MM can take any value from 00 to 59.  Any time Both (From) and (To) may be left blank. Click Apply, to apply the new rule. The Filter

122 URL Filtering The URL Filtering feature of the router makes it easy to block certain websites from LAN users. URL Filtering Selec

123 Selecting Allow In Host Name, enter the web site address to be blocked. For example: www.objectionablewebs

124 Multicast Filtering This feature lets you allow or disallow streaming over the Internet, if you have registered to ISP services providing vid

125 Chapter 10: Web Interface Utilities This chapter describes the use of:  The System Tools menu  The Help menu Using the SYSTEM TOOLS Menu

126 The Ping Utility pings the target with 10 packets of 56 bytes data and displays the results and statistics at the end. Click Back to retu

127 Syslog Syslog allows remote system logging. You can setup Syslog with the following steps. SStteepp 11:: Click on SSyysslloogg from the SSY

128 To Identify Your System If your network operates with several of the access points, a means of identifying each individual access point would

129 Setting the Time of Your System Synchronising the clocks of the router and your workstation enables effective management and operation of the p

130 To Upgrade the Firmware Version The products are designed for upgradability. Click About System from the HELP menu to check your current firmw

5 Additional Features These features reveal the comprehensive range of advanced functionalities when the router is further configured. Static IP,

131 Settings Profile A profile is the set of parameters with which the router is configured. You may choose to:  Save your customised profile 

132 Backup Browse To return system to earlierconfiguration using backup file: 1. Click Browse to search forbacku

133 To Reboot Most changes in system settings require rebooting to take effect. Follow these steps to reboot the router. Reboot System

134 Change Your Login Password The login password is required to access the web configuration interface, through which the router’s settings can be

135 To Logout Follow these steps to logout. Logout Click Logout from the SystemTools menu. A login prompt displays. T

136 Using the HELP Menu To Get Technical Support This page contains the contact information of technical support centres around the world. Follow

137 About Your System The About System page displays a summary of system configuration information that might be required by support technicians du

138 Chapter 11: Printer Server Setup (For NP18 1A, 2B) The router can also act as a network print server that is easy to operate. When its print s

139 Next to add the printer to your PC: 1. Go to the Windows Start Menu; select Settings, then followed by Control Panel. 2. Then double-clic

140 4. When the Add Standard TCP/IP Printer Port Wizard appears, click on the Next> button to proceed. 5. Enter your router’s IP addres

6 When to use which router  NetPassage 18A IB11US, 1A13EU, IB11US, and 1B13EU are dualband wireless A+G VPN Internet router offering simultaneou

141 8. Go to the Protocol section and select LPR. 9. Next proceed to the LPR Settings section. In the Queue Name field, key in ‘usb0’. Please

142 3. Then you will be prompted to choose whether to keep the existing driver or install a new driver. However, it is recommended that you sho

143 9. It is recommended to test the printer. To print the test page, click Yes. When you get the test print out, it means that the printer is

144 Adding A Shared Printer Via LPR in Windows 2000 For Windows 2000 Users Under the HOME USER FEATURES command menu, click on Printer Server Set

145 5. Check the radio button next to the Local printer attached to this computer and click Next> to proceed. Please note that you should n

146 5. Enter your router’s IP address in the Printer Name or IP Address field. Then the corresponding Port Name will be automatically entered.

147 11. After you have successfully configured the selected port, you will see the information display in this window. Click Finish to complete

148 5. Key in the printer’s name, you can make it as the default name. 6. Click on the Next> button to proceed. 7. If you want to sha

149 11. This window displays a summary of the settings of the printer that is successfully installed. 12. To exit the window, click Finish.

150 Adding A Shared Printer Via LPR in Windows 98/ME Before setting up the LPR printer server, you have to download the software of the LPR printe

7 Panel Views The router has been designed such that it can either be placed on a desktop or mounted onto a wall. LED indicators denoting networ

151 3. The Add Printer Wizard (shown on the left) appears. 4. Click Next> to proceed. 5. Click the radio button next to Local Printer.

152 4. At the Install From Disk screen, click Browse... to search for your printer’s driver and install it. 5. The Open screen prompts you t

153 6. Then you will be prompted to choose whether to keep the existing driver or install a new one. But you are advised to keep the existing d

154 12. Right-click on the icon of the printer you have just installed to select Properties. 13. At the Details tab of the printer’s prope

155 17. At the Settings tab of the ACITS LPR Remote Printing screen, key in the router’s IP address. Proceed to key in the printer/queue name. F

156 Removing the Shared Printer from the Router Removing Printer To physically remove the network printer from the router safely, Click on th

157 Chapter 12: USB Storage Disk Sharing (For NP18 1A, 2B) The router connects to your USB hard disk/flash disk to allow easy storage sharing in t

158 Allow Anonymous: Selecting Yes indicates that you allow users to access to your USB storage disk to upload and/or download files without havin

159 Advanced USB Disk Sharing Functions: Show Connections of Server Under the Advanced USB Disk Sharing Functions, click on Show connections to

160 Advanced USB Disk Sharing Functions - FTP Server User Account List Under the Advanced USB Disk Sharing Functions, click on Manage FTP user

8

161 If you wish to delete an existing or current FTP user account, go to the FTP Account Configuration page. Then click on the hyperlink next to

162 Advanced USB Disk Sharing Functions - File Server User Account List Under the Advanced USB Disk Sharing Functions, click on Manage file ser

163 If you wish to edit an account password or delete a user account, go to the File Server Account Configuration page. Then click on the corres

164 Accessing Your USB Hard Disk Via FTP Server Access via FTP Server From your Internet Explorer address bar, type in ftp://192.168.168.1, whe

165 ! Note: The Workgroup Name of both the router and the PC must be the same.Accessing Your USB Hard Disk Via Windows File Server Access via

166 Using Windows File Server to Map to Network Drive This section explains how to connect to the shared USB storage disk attached to the router a

167 To check your USB device share name, refer to USB Devices List as shown below. Notice that the router will define the Share Name as sda or s

168 Chapter 13: Webcam Setup and View (For NP18 1A, 2B) This chapter describes how you may configure the router to set up your webcam so that auth

169 Configuring the Webcam Setup To be able to configure the webcam setup, you have to enable it first. Webcam User Setup Under the HOME USER

170 Enter your Username. For example, ‘demo’. Next enter the Password. Click Add. Then the new user is added in the list. Please note that

9 Panel Description Name Description Steady Green The device is powered up. 1 Power (LED) Off No power is supplied to the device. Steady Gree

171 Webcam List Under the HOME USER FEATURES command menu, click on Webcam Setup. Then go to Camera List. If you have just connected your w

172 Viewing the Webcam If you see the message read: “Please change its status in Webcam Setup”, it shows that you have not enabled the webcam setu

173 Appendix A: Configuring your PC for network access This section illustrates how to configure the TCP/IP settings of your computer so that it c

174 Double-click on the Network icon. The Network Configuration screenshown on the left will appear. Check your list of

175 Configuring Dynamic IP address allocation Microsoft Windows 98/98SE/ME/2000 Follow these steps to configure your PC for dynamic IP address allo

176 1. Click on the IP Address tab. 2. Enable the Obtain an IPaddress automatically radiobutton. 3. Click on the Gateway tab. 4. Ver

177 Configuring Static IP address allocation Microsoft Windows 98/98SE/ME/2000 The following will help you configure your PC with static IP address

178 1. Click on the IP Address tab. 2. Enable the Specify an IPaddress radio button. 3. Fill in the IP Address field as

179 Configuring Wireless Network Settings for Windows XP It is usually recommended to configure the wireless client PC or notebook with automatic I

180 Appendix B: Troubleshooting Solutions to Common Problems In this section, we list suggested steps to rectify some common problems that may a

10 6 External Antennas SMA antennas 7 Rest Feet These rest feet hold the router in the standing position. 8 USB1, USB2 USB Ports (NP18A 1A, N

181 2. I am unable to surf the Internet. A. Make sure that the Ethernet cable is properly connecting your Cable/ADSL modem to the WAN port of th

182 ♦ For Netscape 4.7 or later versions  Start Netscape Navigator. From the Edit menu bar, select Preferences, then Advanced, and finally Pro

183 “This device is working properly”. If it does not, you will need to uninstall and re-install the software driver. C. Verify whether your rout

184 Appendix C CLI Commands Get Operation List SYNTAX DESCRIPTION Get tasks Display all active process/tasks. Get sysinfo Display system infor

185 TX Rate SYNTAX DESCRIPTION Set txrate <string> Values are: (default auto) (802.11a)-- 6, 9, 12, 18, 24, 36, 48, 54, auto (802.11b/g m

186 {CTRY_FRANCE, "FR" }, {CTRY_FRANCE2, "F2" }, {CTRY_GEORGIA, "GE" }, {CTRY_GERMANY, "

187 {CTRY_TUNISIA, "TN" }, {CTRY_TURKEY, "TR" }, {CTRY_UKRAINE, "UA" }, {CTRY_UAE, "

188 WLAN State SYNTAX DESCRIPTION Get wlanstate Display whether status of current wireless operation is Enabled or Disabled. Set wlanstate enabl

189 Appendix D: Glossary of Terms List of commonly used terms 10Base-T An IEEE Ethernet standard for 10Mbps data transmission using unshielded

190 DSSS Direct Sequence Spread Spectrum is a modulation scheme employed by the 802.11b standard that uses a chipping code (redundant bit) durin

i © Copyright 2006 Compex Systems Pte Ltd All Rights Reserved This document contains information that is protected by copyright. Reproduction, adapt

11 13 Reset (Push Button) The table below illustrates the use of the Reset button. Reset Push Button Diagnostic LED Router Behavior Less than 3 s

191 multicast group. All hosts conforming to level 2 of the IP multicasting specification require IGMP. IEEE It is the Institute of Electric

192 PPTP Point-to-Point Tunneling Protocol supports the creation of Virtual Private Networks by ensuring that messages transmitted from one VPN

193 WEP Wired Equivalent Privacy is a wireless data privacy encryption protocol based on a 64-bit or 128-bit shared key algorithm. WLAN Wi

194 Appendix E: Technical Specifications Technical Specification Industrial Standards Wired: • IEEE 802.3 10Base-T • IEEE 802.3u 100Base-Tx •

195 Stateful Packet Inspection (SP I) Firewall Yes Universal Plug and Play Yes Dynamic DNS Service (Subscribe service) Yes Time-based Access Con

12 Chapter 3: Hardware Setup Before attaching a pair of external antennas to the router, take note of the ‘A’ marking on one of the two anten

13 Insert one end of the RJ45 Ethernet cable to any of the LAN ports (1, 2, 3, or 4) on the router and the other end to your PC’s Ethernet network

14 Chapter 4: Accessing the Web interface This chapter consists of the following:  Overview of alternatives to access the web interface  How t

15 After installation, your PC will automatically detect connected products. Double-click on the uConfig utility icon to run the program. Runni

16 How to Browse to the Web Interface Browsing to the web interface You will then reach the home page of the router’s web i

17 Chapter 5: Setting Up a WLAN This chapter applies exclusively to Wireless Setup (a/b/g) and Wireless Setup (b/g). Wireless Setup (a/b/g) sup

18 Operation Modes Access Point Mode This is the default mode of your access point. The Access Point mode enables you to bridge wireless clients to

19 Client Mode In Client mode, the device acts as a wireless Client. When connected to an access point, it will create a network link between the

20 Transparent Client Mode In Transparent Client Mode, the access point provides connection with an AP acting as Root AP. This operation mode is d

ii FCC Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This dev

21 Difference Between other client modes and Transparent Client Mode Other client modes Transparent Client Mode Connectivity with any standard APs

22 To Set Up a Wireless LAN Follow these steps to setup your wireless LAN for IEEE 802.11a, IEEE 802.11b, and IEEE 802.11g. WLAN Setup (a/b/g)

23 Operation Mode : The router supports three types of modes such as Access Point, Client, and Transparent Client. WLAN nam

24 Wireless mode : Select from the list of wireless modes available: 802.11a (not supported by WLAN Setup for b/g) This mode supports

25 Point-to-Point & Point-to-MultiPoint Setup You can implement Point-to-Point connection by simply setting one access point as RootAP in Acc

26 RRoooottAAPP SStteepp 22:: Select AAcctt aass RRoooottAAPP, click on the AAppppllyy button and reboot your device to let your changes take

27 Follow these steps to setup Transparent Client/s. TTrraannssppaarreenntt CClliieenntt SStteepp 11:: Click on WWLLAANN SSeettuupp from the C

28 TTrraannssppaarreenntt CClliieenntt SStteepp 22:: Select the RReemmoottee AAPP MMAACC checkbox. Enter the RReemmoottee AAPP MMAACC.

29 How to Make Your WLAN More Secure All your network clients MUST share the same wireless settings as your router to be able to communicate. The

30  WPA2 Personal WPA2 Personal mode implements the full IEEE 802.11i standard with a shared network password for clients and access points. The o

iii Technical Support Information The warranty information and registration form are found in the Quick Install Guide. For technical support, you m

31 The subsequent sections illustrate how to configure each security mode. Begin with following the two common preliminary steps shown below to se

32 How to Setup WEP WEP You can define up to 4 WEPkeys. For each key, you can specify:  The Key Entry Method, byselecting

33 For hexadecimal key entry: 1. Select the Hex radio button. 2. Select the radio button ofthe key

34 For ASCII key entry: 1. Select the ASCII radiobutton. 2. Select the radio buttonof the key to beentered. 3. Select the keyencrypti

35 How to Setup 802.1x 802.1x 1. Key in the IP address ofthe Primary RADIUS

36 How to Setup WPA Enterprise Modes Follow these steps to setup the router to use WPA Enterprise, WPA2 Enterprise, and WPA Auto Enterprise. WPA E

37 How to Setup WPA Personal Follow these steps to setup the router for using WPA Personal, WPA2 Personal, and WPA Auto Personal. WPA Personal

38 Advanced WLAN Settings Follow these steps to change the radio settings of your router. Editing Advanced Settings 1. Click on W

39 6. Select whether to enable StationIsolation. This security feature implementsisolation, in order to

40 Antenna Control These are the recommended antenna control settings. Antenna Control If both antennas are connected: set antenna control to Di

iv About This Document The products described in this document, Compex Dual Band Wireless A+G VPN Internet Router, NetPassage 18A series are licens

41 Long Distance Parameters It is necessary to adjust the long distance parameters, only if the distance is 100 meters and beyond. Follow these ste

42 1. Select whether to Enable or Disable Outdoor operation. 2. Enter Distance of the unit in meters. 3. Enter the SlotTime. 4. Enter the a

43 WMM Wireless Multimedia (WMM) is a feature specially developed to improve the user’s experience for audio, video, and voice applications by prio

44 Follow these steps to change the setup Wireless Multimedia on your access point. Setting WMM Click WMM Settings. 1. Select to

45 WMM Parameters (for advanced users) AIFs (Arbitrary Inter-Frame Space) Arbitrary Inter-Frame Space is the fixed wait time for different data tr

46 Statistics Follow these steps to view the WLAN detailed connections statistics per WLAN station. Statistics 1. Click on WLAN Setup (a/b/g)

47 Virtual AP (Multiple SSID) Virtual AP implements mSSID (Multi-SSID) whereby a single wireless card can be setup with up to 16 virtual AP connec

48 Follow these steps to setup Virtual AP. Virtual AP 1. Click on WLAN Setup (a/b/g) from the CONFIGURATION menu. 2. Select Virtual AP.

49 Preferred APs (Only available in Client Mode) When there is more than one AP with the same SSID, the Preferred APs function allows you define t

50 Antenna Alignment The antenna alignment function helps you find the best alignment for the antenna by measuring the quality of the signal. For b

i TABLE OF CONTENTS © COPYRIGHT 2006 COMPEX SYSTEMS PTE LTD ...I TRADEMARK INFORMATION...

51 Chapter 6: Configuration This chapter describes the different features of your router and explains how to customise them to meet your network

52 the DHCP Start IP Address should be 192.168.168.X where X is any value from 2 to 254. It is preset to 192.168.168.100. DHCP End IP Address Thi

53 Setting Up Your LAN Follow these steps to change the values and customise them for your LAN settings. LAN Setup Click

54 To view the active DHCP leases The following will guide you to a display of the active IP address leases that have been allocated by the built-i

55 To reserve specific IP addresses for predetermined DHCP clients The ability to make IP reservations enables you to assign a fixed IP address to

56 If you do not need the DHCPserver to reserve an IP addressanymore, you can delete theDHCP Server Reservation: 1. Select the reserved IPad

57 Bandwidth Control for WAN Bandwidth Control allows you to decide the available bandwidth in levels of 1kbit. Follow these steps to setup Bandwi

58 Bandwidth Control for LAN Bandwidth Control allows you to decide the available bandwidth in levels of 1kbit. Follow these steps to setup Bandwi

59 1. Enter the Bandwidth Control Rule Name. 2. Enter the Committed Rate in kbit. This sets the bandwidth committed. 3. Enter

60 STP Setup Spanning Tree Protocol is a link management protocol that provides path redundancy while preventing undesirable loops in the network.

ii How to Setup WPA Personal ...37 ADVANCED WLAN SETTINGS...

61 Priority: Specify the priority given to the AP. This value determines which access point acts as the central reference point, or Root AP, for

62 SNMP Setup SNMP (Simple Network Management Protocol) is a set of protocols that facilitates the exchange of management information between netwo

63 SNMP Trap The SNMP Trap provides notification of significant network events through unsolicited SNMP messages. This results in substantial savi

64 Chapter 7: Enabling and Disabling Router This chapter describes the switching capability of the unit to operate either as a router or access p

65 Setting Up Access Point Follow these steps to disable the router and switch back as an access point. Disable Router

66 Chapter 8: Router Setup This chapter describes the different features of your unit when it is set to operate as a router.  Broadband Internet

67 WAN Setup The configuration for each type of broadband Internet connection is shown in the following individual sections. The system has to be r

68 Static IP If you have subscribed to a specific IP address or to a fixed range of IP addresses from your ISP, follow these steps. Static IP C

69 Dynamic IP This is the default WAN Type of your router. In this connection mode, your ISP will automatically assign its IP address. This con

70 PPPoE Select this connection type if you have subscribed to ADSL in a country utilising standard PPPoE for authentication, for instance:  If y

iii WEB MANAGEMENT SETUP ...95 REMOTE MANAGEMENT ...

71 Follow these steps to setup PPPoE. PPPoE Configuration Select PPP over Ethernet from the Select WAN Type menu.

72 PPTP The Point-to-Point Tunneling Protocol (PPTP) enables the implementation of secure multi-protocol Virtual Private Networks (VPNs) through pu

73 L2TP L2TP (Layer 2 Tunneling Protocol) is an extension to the PPP protocol used for Virtual Private Networks (VPNs) that supports multiple proto

74 Email Notification This feature notifies you by email if there is a change in the WAN IP address. Follow these steps to setup Email Notificati

75 Email address of Sender: This is the email address that will appear as the sender. Needs Authentication specifies whether the SMTP server requ

76 Using NAT NAT (Network Address Translation) functions by transforming the private IP address of packets originating from hosts on your LAN so th

77 When NAT is enabled, your LAN is not accessible to the WAN. However, implementing virtual servers allows you to host Internet servers such as we

DMZ 1. Click NAT from theCONFIGURATION menu. 2. Ensure that NAT Status is setto Enable. At the Advanced NAT Optio

79 To Setup Port Forwarding Port forwarding allows the router to redirect any incoming Internet request bearing a public IP address to a specific P

80 Follow these steps to setup port forwarding. Port Forwarding 1. Click NAT from theCONFIGURATION menu. 2. Ensure that NAT Status i

iv ACCESSING YOUR USB HARD DISK VIA WINDOWS FILE SERVER ...165 USING WINDOWS FILE SERVER TO MAP TO NETWORK DRIVE...

81 The Port Forward Entries table displaysthe list of current port-based entries.

82 NAT Static Port Based Entries reflects the new entry. To assign more servers in your LAN: 1. Click Add. This will bring you b

83 The following is a non-exhaustive list of well-known port numbers: Application Port Number Echo 7 Daytime 13 FTP 21 SMTP (Simple Mail Transfer

84 IP Forwarding If you have subscribed to more than one IP address from your ISP, you may define Virtual Servers based on their IP address so tha

85 NAT Static IP Address Entries reflectsyour new entry. To assign more servers in your LAN: 1. Click Add. This will bring yo

86 Routing The router supports both static routing for manual routing table entry addition, and dynamic routing for automatic routing table update.

87 Static Routing Follow these steps to add entries to your access point’s routing table for rerouting of IP packets to another network. Static Ro

88 The IP Routing Table reflects the newentry. To add more routes: 1. Click Add. This will bring you back to Add IPRoute GUI. 2.

89 Telnet/SSH Setup Telnet allows a computer to remotely connect to the CLI (Command Line Interface) for control and monitoring. SSH (Secure Shel

90 Follow these steps to setup Telnet/SSH. Telnet/SSH Setup 1 Click Telnet/SSH Setup from theDevice Access Managementmenu. 2 1