Compex Technologies WP11A+ Manual de usuario

Table of Contents Appendix III Configuration and Commands on Telnet Interface ... 86 AIII-1 Telnet Interface Configuration...

Appendix III Configuration and Commands on Telnet Interface 90Wait until the DIAG LED starts blinking slowly which may takes about 10 seconds. This i

Appendix III Configuration and Commands on Telnet Interface 91If you have the correct IP address but is still unable to connect to a Web site, then c

Chapter 1 Product Overview 1Chapter 1 Product Overview 1.1 Introduction A wireless network is a convenient way of setting up a network both at home

Chapter 1 Product Overview 21.3 Features and Benefits Compex WP11A+ is designed to give you a complete solution of a wireless network by establishin

Chapter 1 Product Overview 31.3.6 LAN-to-LAN Bridging Compex WP11A+ may also be configured as an Extended Service Set (ESS) Client, working in conjun

Chapter 1 Product Overview 4Figure 1.4b Side view of Compex WP11A+ (Section #1) Figure 1.4c Side view of Compex WP11A+ (Section #2) Figure 1.4dConn

Chapter 1 Product Overview 51.5 Panel Description Indicator Description 1 Power LED Steady Green LightPower is supplied to Compex WP11A+. 2 WLAN LE

Chapter 1 Product Overview 6Indicator Description 9 AP Mode LED Steady Green LightThe device is in AP Bridge Mode or AP Client Mode. No LightThe d

Chapter 1 Product Overview 71.6 Technical Specifications Items Specifications Industry Standards • IEEE 802.3 10Base-T; • IEEE 802.3u 100Base-TX;

Chapter 1 Product Overview 8Items Specifications Media Access Method Carrier Sense Multiple Access with Collision Avoidance (CSMA/CA) Gateway Mode

Chapter 2 Getting Started 9Chapter 2 Getting Started This chapter outlines the basic requirements before you begin any installation and configuratio

iCopyrights © 2002 Compex Systems Pte Ltd All Rights Reserved This document contains information, which is protected by copyright. Reproduction, adapt

Chapter 3 Hardware Installation 10Chapter 3 Hardware Installation Figure 3a Compex WP11A+ Connections To begin setting up the Compex WP11A+, please

Chapter 3 Hardware Installation 112. Place the Compex WP11A+ in a well ventilated area. 3. Place the device in a standing position. 4. Connect you

Chapter 4 Software Configuration 12Chapter 4 Software Configuration After setting up the hardware, install a browser on the PC or workstation. Make

Chapter 4 Software Configuration 13This will automatically launch the program and you will be greeted with the uConfigapplication page as shown in Fi

Chapter 4 Software Configuration 144. Click on the “Log ON!’ button to access the web based configuration interface of the Compex WP11A+. The defaul

Chapter 4 Software Configuration 154.1.1 AP Bridge and AP Client Mode Exit uConfig Mode menu – End the Utility Configuration Program• ExituConfig C

Chapter 4 Software Configuration 16• Reboot System • Change Password • Logout HELP menu• Get Technical Support • About System With this user-fri

Chapter 5 Configure Compex WP11A Using Web Interface 17Chapter 5 Configure Compex WP11A+ Using Web Interface This chapter explains the Configuration

Chapter 5 Configure Compex WP11A Using Web Interface 185.1 Changing the IP Address of Compex WP11A+ You can also assign a specific IP address to the

Chapter 5 Configure Compex WP11A Using Web Interface 19To reserve a certain IP address for a specific workstation1. Click on “DHCP Server Reservatio

iiFCC NOTICE This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These

Chapter 5 Configure Compex WP11A Using Web Interface 205.3 Setting up Wireless Per Group Pseudo LAN using AP Bridge Mode With more wireless networks

Chapter 5 Configure Compex WP11A Using Web Interface 21The physical setup of Per Group Pseudo VLAN is illustrated as shown. Figure 5.3b Physical Set

Chapter 5 Configure Compex WP11A Using Web Interface 222. Click “Apply” button from the Network Mode Setup GUI and the web page for Access Point Set

Chapter 5 Configure Compex WP11A Using Web Interface 23Figure 5.3e Access Point Setup Elaboration of Compex WP11A+ ESSID This is an identifier that

Chapter 5 Configure Compex WP11A Using Web Interface 244. Select Per Group in the Pseudo VLAN pull-down menu as shown below and click the “Apply” but

Chapter 5 Configure Compex WP11A Using Web Interface 256. Click “Add” button. Choose your GroupID and key in the client’s MAC address as shown below

Chapter 5 Configure Compex WP11A Using Web Interface 26NOTE You can store up to 4 Encryption keys in Compex WP11A+. However, only one key can be used

Chapter 5 Configure Compex WP11A Using Web Interface 27You can also have a combination of encryption settings in each Pseudo VLAN setting. The combin

Chapter 5 Configure Compex WP11A Using Web Interface 285.4 Setting up Wireless LAN-to-LAN Bridge Network using AP Client Mode Compex WP11A+ may be c

Chapter 5 Configure Compex WP11A Using Web Interface 29Starting PointWith Compex WP11A+ in its default setting, 1. Activate uConfig program, click on

iiiDeclaration of Conformity Compex, Inc. declares the following: Product Name: Compex 11Mbps Wireless LAN Access Point Model No.: WP11A+ conforms to

Chapter 5 Configure Compex WP11A Using Web Interface 30Figure 5.4c Access Point Client Setup 7. Next, you have the option to choose either 64-bit o

Chapter 5 Configure Compex WP11A Using Web Interface 318. Enter your encryption key. The parameters take in hexadecimals. Figure 5.4e Encryption en

Chapter 6 Setting up Wide Area Network using Gateway Mode 32Chapter 6 Setting up Wide Area Network using Gateway Mode This chapter will elaborate on

Chapter 6 Setting up Wide Area Network using Gateway Mode 33NOTE If you are subscribers of OPTUS in Australia, please select Dynamic IP as your WAN t

Chapter 6 Setting up Wide Area Network using Gateway Mode 346. Next, remove cable from your workstation and insert it into your modem’s Ethernet por

Chapter 6 Setting up Wide Area Network using Gateway Mode 356.3 Configure Compex WP11A+ using Web Interface Figure 6.3a Physical layout for Wireles

Chapter 6 Setting up Wide Area Network using Gateway Mode 363. Go to uConfig program and click on the “OpenWeb” button. Logon again and now Compex WP

Chapter 6 Setting up Wide Area Network using Gateway Mode 375. For details in configuring Pseudo VLAN and WEP encryption method, please refer to the

Chapter 6 Setting up Wide Area Network using Gateway Mode 386.3.1 Advanced configuration in Gateway Mode uConfig IP SetupBy selecting uConfig IP Set

Chapter 7 Setting up WAN using Wireless Routing Client 39Chapter 7 Setting up WAN using Wireless Routing Client Setting Compex WP11A+ as a wireless

iv Technical Support Information The warranty information and registration form are found in the Quick Install Guide. For technical support, you may c

Chapter 7 Setting up WAN using Wireless Routing Client 40Figure 7.1b Physical layout for setting Compex WP11A+ as Wireless Routing Client 4. Power

Chapter 7 Setting up WAN using Wireless Routing Client 417.2 Configuring Compex WP11A+ as Wireless Routing Client through Web Interface Assuming tha

Chapter 7 Setting up WAN using Wireless Routing Client 424. Next, click on the “Apply” button to proceed to the Wireless Routing Client Setup. Figur

Chapter 7 Setting up WAN using Wireless Routing Client 436. Enter your encryption key. The parameters take in hexadecimals. Figure 7.2d Encryption

Chapter 8 Configuration on Various WAN Type 44Chapter 8 Configuration on Various WAN Type This section explains how to configure the Compex WP11A+ a

Chapter 8 Configuration on Various WAN Type 453. The WAN Setup screen shows a Static IP Configuration that allows you to configure your Static IP con

Chapter 8 Configuration on Various WAN Type 468.2 Configuring Dynamic IP Connection The Compex WP11A+ is pre-configured with WAN connection using Dy

Chapter 8 Configuration on Various WAN Type 478.2.2 How to Configure @HOME Cable Service Many broadband services require a simple DHCP request for c

Chapter 8 Configuration on Various WAN Type 488.3 Configuring PPP over Ethernet Session (PPPoE) For Broadband service providers such as Pacific Inte

Chapter 8 Configuration on Various WAN Type 49The WAN Setup screen below displays the PPPoE configuration that allows you to configure your ADSL acce

vAbout This Document The product described in this document, Compex NetPassage Series, Compex WP11A+ is a licensed product of Compex Systems Pte Ltd.

Chapter 8 Configuration on Various WAN Type 508.4 Configuring for SingTel Magix SuperSurf With your ADSL modem and PC, you can configure your WAN us

Chapter 8 Configuration on Various WAN Type 514. Enter Username, Password, Service Name (optional) and Idle Timeout (disabled at default). 5. Click

Chapter 8 Configuration on Various WAN Type 522. Click on “Save” and the Australia BPA Cable WAN Setup screen will appear for you to set the configu

Chapter 8 Configuration on Various WAN Type 538.6 Point to Point Tunneling Protocol (PPTP) PPTP enables implementation of secure, multi-protocol Vir

Chapter 8 Configuration on Various WAN Type 543. Check the PPTP radio button and press the Save button. The configuration page for PPTP will be displ

Chapter 8 Configuration on Various WAN Type 555. Press the Save button followed by the Reboot button to complete the configuration process. 6. Enter

Chapter 8 Configuration on Various WAN Type 563. Check the JTB BruNet e-Speed (Brunei) radio button and press the Save button. The configuration page

Chapter 9 Configuring Network Address Translation 57Chapter 9 Configuring Network Address Translation In this chapter, we will illustrate on how yo

Chapter 9 Configuring Network Address Translation 589.2 Defining Port-Forwarding Virtual Server Port Forwarding redirects any incoming Public IP Int

Chapter 9 Configuring Network Address Translation 592. Click on the “Port Forwarding” button to display the NAT Static Port Based Entries GUI.Figure

Table of Contents Copyrights © 2002 Compex Systems Pte Ltd ... i Trademark Information

Chapter 9 Configuring Network Address Translation 60If you require assigning more PCs in your LAN as servers, use the “Add” button to define the port

Chapter 9 Configuring Network Address Translation 613. Click on “IP Forwarding” button. Figure 9.4b Adding New NAT IP address Entry Enter the infor

Chapter 10 Routing 62Chapter 10 Routing 10.1 Configuring Routing Protocol You can configure Compex WP11A+ to either Dynamic or Static Routing Proto

Chapter 10 Routing 63You will set the desired Destination IP Address and the Gateway IP Address. 2. Click “Apply” button to save your changes. You n

Chapter 11 Packet Filtering 64Chapter 11 Packet Filtering 11.1 Filtering Compex WP11A+ allows Packet Filtering rules to be defined based on three fa

Chapter 11 Packet Filtering 65To add a new rule1. Press “Add” button. The screen facilitates the users to add rules for IP Packet Filtering. Figure

Chapter 11 Packet Filtering 66To delete a rule1. Select the required rule on the Select to Edit column. 2. Click on Delete to activate the action. T

Chapter 12 Remote Management 67Chapter 12 Remote Management 12.1 Remote Management The Remote Management feature is a useful function for those peop

Chapter 13 Using SYSTEM TOOLS menu 68Chapter 13 Using SYSTEM TOOLS menu 13.1 System Identity If you have multiple Compex WP11A+s in your network, it

Chapter 13 Using SYSTEM TOOLS menu 6913.2 Set System Time It is recommended that you configure the Compex WP11A+’s timer to synchronize with your PC

Table of Contents 4.1.2 Gateway and Wireless Routing Client Mode ... 15Chapter 5 Configure Compex WP11A+ Us

Chapter 13 Using SYSTEM TOOLS menu 7013.3 Firmware Upgrade You can download the new Firmware upgrade from http://www.compex.com.sg for the latest fir

Chapter 13 Using SYSTEM TOOLS menu 7113.4 Save or Reset Settings This function allows the users to perform tasks on the configuration settings. You

Chapter 13 Using SYSTEM TOOLS menu 72To BackupTo backup Compex WP11A+’s configuration into a file, click on the “Backup” button. To RestoreClick on t

Chapter 13 Using SYSTEM TOOLS menu 7313.6 Change Password This option allows the System Administrator to amend the current password. The default pass

Chapter 13 Using SYSTEM TOOLS menu 7413.7 Logout With the web browser, logging out has never been easier. Simply click on the “Logout” button and you

Chapter 13 Using SYSTEM TOOLS menu 75Figure 13.8a uConfig icon at the taskbar uConfig icon will disappear after clicking on the exituConfig bar.

Chapter 14 Using HELP menu 76Chapter 14 Using HELP menu 14.1 Get Technical Help For more information on Compex’s technical support around the world

Chapter 14 Using HELP menu 7714.2 About System You can check the various configuration of the Compex WP11A+ by clicking on the About System menu. Aft

Chapter 15 Hardware Reset of Compex WP11A 78Chapter 15 Hardware Reset of Compex WP11A+ The Compex WP11A+ is designed with a reset button located at

Appendix I Login to Web-based Interface manually 79Appendix I Login to Web-based Interface manually AI-1 Configuration of Compex WP11A+ using Web-b

Table of Contents Chapter 10 Routing... 6210.1 Configuring Routing Protocol.

Appendix I Login to Web-based Interface manually 80In Netscape Communicator1. Select the File menu, and then click on the Open Page.2. In the Open Pa

Appendix II TCP/IP Configuration 81Appendix II TCP/IP Configuration This section discusses the configuration of your TCP/IP connection of your Compe

Appendix II TCP/IP Configuration 823. Check your list of Network Components in the Network window Configuration tab. If TCP/IP is not installed, cli

Appendix II TCP/IP Configuration 836. After TCP/IP is installed, go back to the Network screen and select TCP/IP in the list of Network Components.

Appendix II TCP/IP Configuration 84AII-2 TCP/IP network protocol configuration for Windows XP/2000 For Windows XP/2000 users, you do not need to ins

Appendix II TCP/IP Configuration 853. Select the Internet Protocol (TCP/IP) item and click on the “Properties” button. Figure AII-8 IP Address Conf

Appendix III Configuration and Commands on Telnet Interface 86Appendix III Configuration and Commands on Telnet Interface AIII-1 Telnet Interface C

Appendix III Configuration and Commands on Telnet Interface 87AIII-2 Command Line Interface Commands List Command Examples ping <d.d.d.d> sho

Appendix III Configuration and Commands on Telnet Interface 88Command Examples show tcp stat show ethernet address show gateway set gateway <d.d

Appendix III Configuration and Commands on Telnet Interface 895. Go to Recovery folder and activate wp11arcv.bat.The system will go to DOS Prompt au